Warning: session_start() [function.session-start]: open(./tmp/sessions/sess_36b3b13a54ff78e2f42cee9070bef1ab, O_RDWR) failed: Disk quota exceeded (122) in /home/tmhoh/public_html/kencotoyotalift.com/include/common.php on line 11
Kenco Toyotalift

ELECTRIC WALKIE PALLET JACK

PALLET JACK

  • 4,500 lbs. Lifting Capacity
  • Galvanized Option
  • AC-Powered
  • Length to forkface 53.4 - 81.4 in
  • Height (Extended Handle) 47.2 in
  • Overall Width 28 in

The Toyota Electric Walkie Pallet Jack makes pulling product through the warehouse efficient and convenient. Ideal for mid-distance runs as well as loading and unloading trailers, the Electric Walkie Pallet Jack is a handy, multi-use solution for nearly any application.



OPERABILITY AND ERGONOMICS

  • Multifunction Control Handle with Ergonomically Angled Hand Grips
  • Fingertip Control of all Functions
  • Directional Thumb Wheels
  • Programmable Neutral Speed Reduction
  • Direction Reverse Switch on Control Handle
  • Turtle Torque
  • Spring-Loaded Control Handle
  • "Pinwheel" Capability for Right Angle Stacking
  • Electric Disc Brake
  • Emergency Power Disconnect
  • Battery Disconnect Handle
  • Electronic Brake Release Jumper

PERFORMANCE

  • 24 Volt Electrical System
  • AC Drive Motor with Thermal Protection & Current Limiting
  • Class 'F' Motor Insulation
  • Transistor Drive Control System (MOSFET)
  • Controller Area Network (CAN-Bus) Communication
  • Regenerative Braking
  • Contactor-less Drive Controls
  • Electronic Touch-Pad, Keyless Entry System with Password Protection
  • Programmable Performance for up to 10 Operators
  • Electronic Raise and Lower Controls in Operator Handle
  • Auto-Off System (programable)
  • Error Indicator with Self-Diagnostics
  • Fault Code Memory with Hour Meter Reading
  • Hour Meter Indicator
  • Programmable Service Indicator
  • Battery Discharge Indicator with lift interrupt
  • Anti-Roll Back System
  • Fused Control and Power Circuits
  • IP65 Rated Electrical System

BODY/EXTERIOR DESIGN

  • Box Rail Fork Construction
  • Tapered Fork Tips with Pallet Entry Slides
  • Polyethylene Stability Wear Pads (Reversible)
  • Teflon« Coated Polylube™ Bushings
  • Chrome-Plated Lift Cylinder, 2" dia.
  • Rubber Drive Tire, 10" dia. x 5"
  • Polyurethane Load Wheels, 3.25" diameter x 4.5" width
  • Battery Compartment 26.5" x 7.8" x Open Height
  • SB-175 Battery Connector (Red)
  • High Strength Service Cover with Pen/Pencil Storage Tray
  • Tool-free cover removal
  • Steel Fixed Pull Rods
  • Electric Horn
  • Stainless steel lift linkage pins

OPTIONS

  • Galvanized Chassis Suited for customers who move materials in and out of: cold storage facilities; chemical and salt and brine industries; or in areas where frequent wash down is required to remove contaminants.
  • Nexsys Maintenance Free Battery/Charger Pack A maintenance free battery pack manufactured by the company Nexsys. Comes with a built in 24 volt battery charger.
  • 3" Lowered Fork Height (3,000 lb capacity) The lowered fork height makes it easier to get into pallets (more clearance with a shorter fork). With this option, the carrying capacity of the pallet jack drops to 3,000 lbs.
  • Sealed-Bearing Dual Load Wheels Sealed bearing dual load wheels use a sealed bearing which make them maintenance free (no need to grease). Dual wheels help in applications where turning is frequent.

SPECIFICATION CHART

Model Number Load Capacity* (lbs.) Max. Travel Speed Full Load (MPH) Max. Lift Speed Full Load (FPM) Max. Gradeability Full Load (%) Basic Right Angle Stack** (IN.)
8HBW23 4,500 3.6 N/A 10 N/A

* Based on 24" load center.
** Add load length and clearance.